X6 Charger Not Supported btemp resistor location
Friday, October 31, 2014
Hard Reset Karbonn Smart Tab 1
Follow these steps to hard reset karbonn Smart Tab1 with a simple method. All data will be deleted from The Tab memory. But no effect happen simcard contacts an mmc card. ofter hard reset your phone looks like New as from company. Here is steps to Hard reset ,factory reset Karbonn Smart Tab1.
Hard Reset Karbonn Smart Tab1
1. Switch off your Tab.
2. Press Volume key Down & POWER key, Hold These Two keys 3 seconds.
3. Ofter 3 seconds Release Power Key and keep holding the Volume down key until you see Recovery menu.
4. Now choose option wipe data.
5. For moving up and down use volume keys to select wipe data.
6. Then Press Button as ok to confirm...
7. Reboot Tab1.
I hope this post ..How To Hard Reset Karbonn Smart Tab1.. Helps you To solve your karbon smart Tab1 problem..
2. Press Volume key Down & POWER key, Hold These Two keys 3 seconds.
3. Ofter 3 seconds Release Power Key and keep holding the Volume down key until you see Recovery menu.
5. For moving up and down use volume keys to select wipe data.
6. Then Press Button as ok to confirm...
7. Reboot Tab1.
I hope this post ..How To Hard Reset Karbonn Smart Tab1.. Helps you To solve your karbon smart Tab1 problem..
Watch this Tutorial:
Thursday, October 30, 2014
Nokia C2 01 Not Charging Problem Solution Jumper Ways
Nokia C2-01 shows not charging notification in it. It can be fault of charging ic or r22 resistance. While if it did not show any notification it may can be fault of missing components or It can be fault of Charging Base Nokia 2320 Classic Not Not Charging Problem Solution Jumpers see see all cellular mobile repairing solution.So In first step replace charger and if problem can not be solve with replacement of charger Dis assemble the mobile phone.
Change charging pin and try again if still charging problem remain same check all these tracks and parts that are given in above diagram. If any path or component is missing apply jumpers as identified in above repairing diagram for Nokia C2-01 not charging problem.
for more detail and new tips and tricks about cellphone service problem keep visiting this page we will update cellphone service diagrams timely with new cellphone diagrams.some related post are also given bellow you can read them also for more information about cellphone.
Nokia 5630 Charger no response solution not charging repair guide
Heres a simple solution guide to fix and repair nokia 5630 charging problem. The picture below shows the location of the chip fuse and chip diode that holds the voltage from the battery charger.
Nokia 5630 Charger No response solution ( charging problem repair)
You may check and replace this components if the device has no charger response indication when the charger is being plug-in.
Nokia 5630 Charger No response solution ( charging problem repair)
You may check and replace this components if the device has no charger response indication when the charger is being plug-in.
Wednesday, October 29, 2014
How to Hard Reset HTC Droid Eris
HTC Droid Eris Hard Reset
Perform a hard reset on your HTC Droid Eris. These steps will clear all data and settings off the device.1. With the phone turned off, press and hold the Volume Down and Send buttons.
2. Press the Power button.
3. Follow the instructions to complete the hard reset.
Nokia X6 Charger Not Supported Solution
Heres a solution that shows the location of BTEMP resistor that caused Charger Not supported on Nokia X6 if damaged. This components needs to replace if cahrger not supported shows on the LCD screen display when the battery charger is being plug-in.
This Btemp resistor rated value is 47K. You may easily find it on other non working Nokia PCB board.
Nokia 5030 Charging problem solution Charger No Response Repair solution
Having a Charger No Response indications is a sign of a defective battery charger, charging pin connector and some of the components on the PCB Board like the chip fuse is being busted or damaged.
This solution below may possibly help fix and repair Nokia 5030 Charger no response indication. It shows the location of chip fuse on the main pcb board that needs to check and replace when a charger no response occurred.Nokia 2690 Earpiece Speaker No Audio Sounds Solution
The chip diode may also damaged and cause short circuit, a shorted diode make the chip fuse blown again, replace it if found shorted.
Read More..
This solution below may possibly help fix and repair Nokia 5030 Charger no response indication. It shows the location of chip fuse on the main pcb board that needs to check and replace when a charger no response occurred.Nokia 2690 Earpiece Speaker No Audio Sounds Solution
Nokia 5030 Charger No response solution (Not charging Repair)
Tuesday, October 28, 2014
Nokia X6 Send E60 and END keypad keys failure solution
If the Send, E60 and End key button keys failed to respond on Nokia X6, and you already tried to restore, reset, flash and update the device firmware but nothing happens.
Keypad keys malfunction on Nokia X6 may also possibly caused by a faulty keypad flex, cleaning or by replacing it will help solved the problem.
If after replacing and ensuring that the flex is okay but the keys still unresponsive, you may then consider that the problem lies on a faulty keypad circuits hardware components on the PCB board. This solution below will tell us which components holds and controls the keypad keys to function or work.
Check the keypad pin connector first ensure that it is free from dirt and oxidation.
From the keypad pin connector there are three line filter coils located near to it, have a check on this components and replace if found damaged.
From the keypad filter coils the lines is feeds to a keypad filtering chip or keypad IC, you may then check this chip, trace its line paths and replace if found damaged.
The I/0 Expander Chip is the keypad controller components, which holds and control the keypads including the Touch Control Module. You may also rework or replace this chip for further harder keypad problem repair on Nokia X6.
Read More..
Keypad keys malfunction on Nokia X6 may also possibly caused by a faulty keypad flex, cleaning or by replacing it will help solved the problem.
Nokia X6 joystick flex cable wire
If after replacing and ensuring that the flex is okay but the keys still unresponsive, you may then consider that the problem lies on a faulty keypad circuits hardware components on the PCB board. This solution below will tell us which components holds and controls the keypad keys to function or work.
Nokia X6 Send, E60 and End key malfunction solution
From the keypad pin connector there are three line filter coils located near to it, have a check on this components and replace if found damaged.
From the keypad filter coils the lines is feeds to a keypad filtering chip or keypad IC, you may then check this chip, trace its line paths and replace if found damaged.
The I/0 Expander Chip is the keypad controller components, which holds and control the keypads including the Touch Control Module. You may also rework or replace this chip for further harder keypad problem repair on Nokia X6.
Nokia C5 00 Keypad problem solution and IC Jumper
Nokia C5-00 keypad problem, Keypadnot working in Nokia c5-00, Keypad Ic ways, Keypad Ic Jumpers can be found in this post to solve keypad problems in Nokia C5-00.Look at diagram bellow and find these parts that are used in keypad work of Nokia C5-00.Nokia 2320 keypad is not working it can be cause of water damage or broken parts.In this problem
Clean these parts that are used in keypad function of Nokia c5-00 and apply heat with hot air to dry them. Do not apply much heat it can damage the motherboard and may can harm you skin.
you can check keypad strip and these ic’s and replace them to solve keypad fault in Nokia C5-00.
for more detail and new tips and tricks about cellphone service problem keep visiting this page we will update cellphone service diagrams timely with new cellphone diagrams.some related post are also given bellow you can read them also for more information about cellphone.
Clean these parts that are used in keypad function of Nokia c5-00 and apply heat with hot air to dry them. Do not apply much heat it can damage the motherboard and may can harm you skin.
you can check keypad strip and these ic’s and replace them to solve keypad fault in Nokia C5-00.
for more detail and new tips and tricks about cellphone service problem keep visiting this page we will update cellphone service diagrams timely with new cellphone diagrams.some related post are also given bellow you can read them also for more information about cellphone.
Monday, October 27, 2014
Nokia 6700c Microphone MIC Mouthpiece Problem solution
Heres the solution that might possibly help fix Noki 6700 classic with a not working mouthpiece microphone problem. This solution may serve as a guide to troubleshoot the mic circuit on nokia 6700c.
The Nokia 6700 classic digital microphone module is being mounted or connected to the keypad UI ( user interface) flex assembly. You may need to check the UI flex first for possible damaged and replace it, if found out. The solution below shows the connection line paths of the microphone on nokia 6700 classic. You may need to check this connection line paths too; Before replacing the microphone module.
The highlighted components and tracing spots on the solution above is useful for a wet damaged nokia 6700c for this line paths may possibly cut-off and result to microphone problem on nokia 6700 classic
The Nokia 6700 classic digital microphone module is being mounted or connected to the keypad UI ( user interface) flex assembly. You may need to check the UI flex first for possible damaged and replace it, if found out. The solution below shows the connection line paths of the microphone on nokia 6700 classic. You may need to check this connection line paths too; Before replacing the microphone module.
Nokia 6700c Microphone ( MIC - Mouthpiece ) Problem solution - MIC ways
Nokia 1800 and Nokia 1616 Charging problem solution
This solution shows the complete line paths of Nokia 1800 and Nokia 1616 charging circuit connections that can be used for repairing charging problem issues on the device such as, Not charging, Charging no response when inserted or it does not show charging indication when a charger is being plug-in.
Repair Procedure on Nokia 1800 and Noki1616 not charging problem.
procedure below may varies accordingly from case to case basis.
1. Check the charging pin connector if its free from dirt and corrosion. Clean it if corroded or find a replacement spare on it then replace it.
2. Check and clean the charging pin connector terminal contact pads.
3. Check the chip fuse if it is busted or damaged by using a multimeter. If found damaged, check the chip diode if shorted. Replace both of it the dont apply jumper on the chip fuse, this method can still save the phone in the future, if you apply jumper on it directly the phone will be dead if a short circuit happen on that particular area again and other than that, its so very unprofessional way.
You can easily find a replacement of this spare parts component to other non working PCB board.
4. Check all the components remaining as shown on the solution picture, a resistor marked R2200 is a fusible resistor which has a value of 0.55 ohms. This resistance value consider as fusible and may easily break or cut if a short circuit has occurs like a water damaged devices.
5. Those transistor shown in the solution image is the voltage regulator that holds and control the charging voltage from the battery charger. The small one has six legs on it and the other one which the big has three legs, just refer to the PCB board layout of your device for the exact component layout.
replace both of it if not so familiar to check those components.
6. The last part needs adequate experience to perform if all of the above does not solve the problem,
Take note: you may do this at your own risk.. just dont do it if your just a beginner or you may end up killing the phone. re-flowing and reworking the X-gold 110 chip needs extra care and proper training.
Nokia 1616 and Nokia 1800 Not Charging Solution ( circuit connection line paths )
Nokia 1616 and Nokia 1800 charging ways
Repair Procedure on Nokia 1800 and Noki1616 not charging problem.
procedure below may varies accordingly from case to case basis.
1. Check the charging pin connector if its free from dirt and corrosion. Clean it if corroded or find a replacement spare on it then replace it.
2. Check and clean the charging pin connector terminal contact pads.
3. Check the chip fuse if it is busted or damaged by using a multimeter. If found damaged, check the chip diode if shorted. Replace both of it the dont apply jumper on the chip fuse, this method can still save the phone in the future, if you apply jumper on it directly the phone will be dead if a short circuit happen on that particular area again and other than that, its so very unprofessional way.
You can easily find a replacement of this spare parts component to other non working PCB board.
4. Check all the components remaining as shown on the solution picture, a resistor marked R2200 is a fusible resistor which has a value of 0.55 ohms. This resistance value consider as fusible and may easily break or cut if a short circuit has occurs like a water damaged devices.
5. Those transistor shown in the solution image is the voltage regulator that holds and control the charging voltage from the battery charger. The small one has six legs on it and the other one which the big has three legs, just refer to the PCB board layout of your device for the exact component layout.
replace both of it if not so familiar to check those components.
6. The last part needs adequate experience to perform if all of the above does not solve the problem,
Take note: you may do this at your own risk.. just dont do it if your just a beginner or you may end up killing the phone. re-flowing and reworking the X-gold 110 chip needs extra care and proper training.
Sunday, October 26, 2014
How to flash Clockwork Mod Touch Recovery 6 0 1 2 for Galaxy S3 I9300
For make this update, please notes this tutorial could only have applied on rooted Samsung Galaxy S3 device. When you will install this recovery, you’ll be able to use custom ROMs firmware.
For be able to guide you need quick pre requisites to follow:
Warning
- The instructions in this guide are intended for use with Galaxy S3 GT I9300 smartphone International version.
- Applying these instructions on another device or model may produce undesired outcomes.
- The information in this guide is provided for instructional and educational purposes only. There is no guarantee that these instructions will work under your specific and unique circumstances.
- Use these instructions at your own risk. We shall not hold any responsibility or liability for whatever happens to you or your device arising from your use of the info in this guide.
- Read and understand the whole guide first before actually performing the instructions.
- This custom recovery image is only for Galaxy S3 GT I9300 smartphone International version, and we will apply only for this model. If you apply on the network / boot loader locked devices.
For SMS-you can use SMS backup and restore tutorial;
For contacts, you can use Sync with your Gmail tutorial;
For Call Logs, use Download Call Logs Backup & Restore App For Android;
For all Images, Video, Files, Songs- Should Copy to internal/ External SD card;
For save your APN and MMS Settings -“Applications > Settings > Wireless and Network > Mobile Networks > Access Point Names” or you can use this tutorial for save your internet settings.
- Check your battery on your phone and charge it at a minimum is not less than 40%.
- Go to access this path “Settings > Applications > Development > USB debugging”, and there verify if you’ve enable the USB Debugging, if not enable it.
- Turn off all the antivirus protection and firewall tools, these can interrupt the proccess of firmware update.
- Check if your device is rooted or not, for make this, please download the “Root Checker” application from here.
- Verify again if you made all this prerequisites above mentioned and now you can forward the next instructions where we have detailed a guide on:
Guide to Install Custom Recovery Image in Samsung Galaxy S3 I9300:
- Download the Latest Clockwork Mod Touch Recovery 6.0.1.2 Image.
- Download Odin from here to your computer.
- Connect your phone on your computer with your original USB cable.
- Place this recovery file on your external SD Card, not in internal memory
- Now disconnect your phone from your computer and turn off the device, to enter in the Download Mode.
- To enter on Download mode, please holding the Volume Down button+ the Home Key button which it is in the middle. Note: If your phone starts in “Normal Mode” retry the process to enter in Download Mode.
- Open Odin app, from your computer, and connect your device on “Download Mode”. Now check if the ID: COM section in Odin becomes Blue that indicating drivers have been successfully installed.
- Click on “PDA” to select “CF-Root-SGS3-v6.4.tar” file.
- Press “Start” after the file was selected to start the process of custom recovery installation.
The device will restart, and the home screen will be displayed on your device, now you can disconnect your phone to the computer.
Attention Note: If your Samsung Galaxy S III doesn’t turn ON(just in a rare case) or say gets stuck on the Samsung Galaxy Logo, in this case you need to long press the power button to power off the device, or re insert the battery to start the process from the begin.
Saturday, October 25, 2014
Nokia 2710NE Keypad repair solution keypad IC flex and pin connector line tracks
This solution shows the connection of the Nokia 2710 navigation edition keypad connections from the keypad matrix flex through to the keypad pin connector and keypad filter ICs.Nokia N78 Earpiece Speaker No Sounds Repair solution
And this solution below show the keypad connection from each particular solder ball bumps of the keypad filter IC. This also includes the nokia 2710ne camera switch connection tracks
Read More..
2710 Keypad keys connection configuration on the flex keypad matrix
And this solution below show the keypad connection from each particular solder ball bumps of the keypad filter IC. This also includes the nokia 2710ne camera switch connection tracks
Nokia 2710 keypad IC jumper with camera switch line tracks
Nokia 7510s Intgrated Hands Free mode loud speaker solution
This repair solution covered for Nokia 7510 supernova Hands Free Speaker Failure. The speaker failed to have no audio sound output when trying to activate the hands free mode our loud speaker option. This solution simply shows and tell us the location of the spare components that might cause the speaker failure.
Ensure that the Speaker is perfectly working before trying to use this solution. This solution may only help if the said speaker is working fine.
The solution only shows the possible components that might cause the problem if the loud speaker does not have and audio sound output. The components on the layout is composed of the filter coils and a protection filter that looks like a chip resistor. You may check those certain components by checking the chip filter coils continuity using a multimeter. Those two black colored components are ESD protection resistor, you may check it also if shorted or not, replace it if found shorted, removing it and leave it open, also works but not advisable.
Ensure that the Speaker is perfectly working before trying to use this solution. This solution may only help if the said speaker is working fine.
Nokia 7510s Hands Free Mode / Ringer loud Speaker solution
Friday, October 24, 2014
Blackberry 9700 cellular phone ringer speaker ok ear speaker not work repair solution
blackberry 9700 cellular phone ringer speaker ok ear speaker not work repair solution many time water damage phone ringer speaker working but ear not working only working ringer if u need any this type solution i have 100% working this phone model solution see this
blackberry 9630 cellular phone usb not connect repair solution
this solution working many solution , blackberry speaker not working ,blackberry speaker low ringer solution ,blackberry 9700 ringer working but ear not working repair guid.
this solution see my diagram and see this parts 1st try this reheat not solved try 2nd time change all parts for yellow color mark 1nd enjoy your phone blackberry 9700 ear not working solution
Thursday, October 23, 2014
Blackberry 9900 cellular phone battery connecter repair ways solution
Blackberry 9900 cellular phone battery connecter repair ways solution many time phone battery connector line damage no have line for phone this problem have working solution only see my solution and try this jumper i think 100% working your battery connector problem solved and again working phone
Blackberry 9860 cellular phone charging ways 100% working solution
this solution my phone solved this solution try this blackberry 9900 battery connector not working connect battery with phone but not on phone this problem solved my solution see my solution blackberry 9900 battery connector line damage solution blackberry battery connector guide solution blackberry battery in but not on phone solution try step by step 100% solved your problem.
Blackberry 8100 battery cross icon solution 100 tested jumper solution
blackberry 8100 battery cross icon solution,blackberry 8100 red light blink solution, blackberry 8100 battery icon cross red light blinking solution 100% tested solution ,blackberry 8100 put battery power not on solution here,blackberry 8100 power not working only red light blinking solution ,blackberry put battery set display cross icon solution many time tested solution this try this solution 100% tested solution blackberry 8100 battery cross icon solution,
blackberry 7290 Light Solution Jumper Solution 100% tested solution
many time tested solution this blackberry 8100 battery cross icon solution if u need battery cross icon for blackberry 8100 see this jumper way 100% tested solution see line and jumper now i hope solve your battery cross icon solution
Blackberry 9860 cellular phone charging ways 100 working solution
Blackberry 9860 cellular phone charging ways 100% working solution see my solution and try this your phone charging problem i hope solved your phone problem for my solution many time water damage phone not show charge and not save phone charging this solution working blackberry 9860 charging ways only line damage solution
Blackberry 9800 cellular phone sim ways solution
see my line and jumper step by step i think solved your phone charging problem 100% working now this solution many time tested see jumper line and dont forget visit my blog.
SamsungGalaxy Ace GT S5830i Update Guide S5830ZXXMK1 Android 2 3 6 Gingerbread Firmware
SamsungGalaxy Ace GT-S5830i [Update Guide] S5830ZXXMK1 Android 2.3.6 Gingerbread Firmware,
If your Galaxy Ace S5830 already running on the Android 2.3.6 Gingerbread, then you can only expect few bug fixes and performance enhancement with this latest firmware update. It is always recommended to update device to the latest available firmware.S5830ZXXMK1 Android 2.3.6 Gingerbread Firmware Last Updated on 22-Feb-2014. Update the latest ZXXMK1 Android 2.3.6 Gingerbread official firmware on Samsung Galaxy Ace GT-S5830i Smartphone. Samsung recently rolled out the firmware. The latest firmware build version is S5830ZXXMK1. The Galaxy Ace S5830i was released back in the year 2011 with Android 2.2 Froyo and receiving Android 2.3.6 Gingerbread from the beginning of the previous year (2012). There is no news about any Jelly Bean update for the device. If you not yet update your device to this latest official firmware, then you can now update the same using our simple tutorial below. You can check latest available firmware for your device through OTA (over the air) from Settings-About Phone-Software Update.
So, want to update your Galaxy Ace S5830i to the latest ZXXMK1 Android 2.3.6 Gingerbread firmware? For official process, either you can go for OTA update by following the above mentioned path or download and update firmware through the Samsung Kies utility. However, most of us prefer manual way to update official firmware. So, in this article you’ll find step by step manual guide to update the latest Android 2.3.6 ZXXMK1 firmware on your Galaxy Ace S5830i through Odin.
Android 2.3.6 Gingerbread S5830ZXXMK1 Official Firmware Download List
Samsung rolled out the firmware for the following countries. The firmware which are unbranded or not locked to any carrier, no matter of which country or region, can be flashed on any Galaxy Ace GT-S5830i model.
Russia: S5830ZXXMK1_S5830ZOXEMC2_SER.zip
Russia: S5830ZXXMK1_S5830ZOXEMC2_SER.zip
[Firmware for rest of the countries and carrier will be added here when available]
How to Install Android 2.3.6 Gingerbread Official Firmware on Galaxy Ace S5830i through Odin:
- Download Android 2.3.6 ZXXMK1 Firmware for Galaxy Ace S5830i from the above list
- Download Odin 3.07
- Switch off your phone and boot Galaxy Ace S5830i into Download Mode by pressing and holding the Volume Down+Home+Power buttons (long press until the boot screen appear), now press Volume Up key to proceed to Download Mode.
- Extract the downloaded Odin3.07 zip file and run the Odin3 v3.07.exe file as an administrator (Right click on the .exe file and click on Run as administrator)
- Now connect your Galaxy Ace S5830i to your computer via USB cable
- In Odin3 screen, you should see a COM Port number like “0:[COM7]” at ID:COM section and “Added!” text at the message box. This means your device has been detected by Odin3.
- Make sure that, only the “Auto Reboot” and “F. Reset Time” options are checked.
- Now, extract the downloaded firmware zip file, you’ll find a firmware file with extension .tar.md5
- In Odin screen, click on PDA button and select the firmware file with .tar.md5 extension (The firmware file look something like: S5830XXDLJ5_S5830ODDDLI7_INU.tar.md5)
- Now, click on the Start button to begin the installation process, wait few moments.
- Once completed, you would see “PASS!” message in ID:COM port having green background
- Your phone should automatically reboot after completion
- You can now disconnect your phone from computer
- Finish
Samsung Galaxy S4 Mini GT I9195 Installation Guide I9195XXUBMK3 Android 4 2 2 Jelly Bean Firmware
Samsung Galaxy S4 Mini GT-I9195 [Installation Guide] I9195XXUBMK3 Android 4.2.2 Jelly Bean Firmware,
![oden]()
I9195XXUBMK3 Android 4.2.2 Jelly Bean Firmware Last Updated on 22-Feb-2014. Samsung Galaxy S4 Mini GT-I9195 (LTE variant) received a new official firmware update which is XXUBMK3 Android 4.2.2 Jelly Bean. Samsung started rolling out an OTA update about the firmware for several countries. The latest firmware build version is I9195XXUBMK3. The Galaxy S4 Mini started receiving firmware update from September 2013 and already get many update by Samsung. If you yet to update your device then you can now update this latest firmware using our simple tutorial below. The below guide will help you to download and install the I9195XXUBMK3 Android 4.2.2 Jelly Bean Firmware manually through Odin. You can also check latest available firmware for your device through OTA (over the air) from Settings-About Phone-Software Update.
The Galaxy S4 Mini LTE was released with Android 4.2.2 Jelly Bean and yet to received any further Android version. As the device already running on Android 4.2.2 Jelly Bean, you can only expect few bug fixes and performance enhancement with this latest firmware update. So, want to update your Galaxy S4 Mini I9195 to the latest XXUBMK3 Android 4.2.2 Jelly Bean firmware? To install in official way, either you can go for OTA update as mentioned above or download firmware through the Samsung Kies utility. However, most of us prefer manual way to update official firmware. So, in this article you’ll find step by step manual guide to update the latest Android 4.2.2 XXUBMK3 firmware on your Galaxy S4 Mini I9195 through Odin.
The Galaxy S4 Mini LTE was released with Android 4.2.2 Jelly Bean and yet to received any further Android version. As the device already running on Android 4.2.2 Jelly Bean, you can only expect few bug fixes and performance enhancement with this latest firmware update. So, want to update your Galaxy S4 Mini I9195 to the latest XXUBMK3 Android 4.2.2 Jelly Bean firmware? To install in official way, either you can go for OTA update as mentioned above or download firmware through the Samsung Kies utility. However, most of us prefer manual way to update official firmware. So, in this article you’ll find step by step manual guide to update the latest Android 4.2.2 XXUBMK3 firmware on your Galaxy S4 Mini I9195 through Odin.
Android 4.2.2 Jelly Bean I9195XXUBMK3 Official Firmware Download List
Samsung rolled out the firmware for the following countries. The firmware which are unbranded or not locked to any carrier, no matter of which country or region, can be flashed on any Galaxy S4 Mini GT-I9195 model.
Spain (Yoigo): I9195XXUBMK3_I9195YOGBMK2_YOG.zip
Poland: I9195XXUBMK3_I9195OXXBMK2_XEO.zip
Slovakia: I9195XXUBMK3_I9195OXXBMK2_ORX.zip
Italy: TIM-I9195XXUBMK3-20131203140511.zip
Spain: PHE-I9195XXUBMK3-20131126131136.zip
Poland: I9195XXUBMK3_I9195OXXBMK2_XEO.zip
Slovakia: I9195XXUBMK3_I9195OXXBMK2_ORX.zip
Italy: TIM-I9195XXUBMK3-20131203140511.zip
Spain: PHE-I9195XXUBMK3-20131126131136.zip
Germany (E-Plus): I9195XXUBMK3_I9195EPLBMJ1_EPL.zip | Link2
[Firmware for rest of the countries and carrier will be added here when available]
All the above pre-requisites are very important and must follow before proceed to installation guide. Hope you get all the above points. Now, go through the below tutorial to install Android 4.2.2 I9195XXUBMK3 official firmware on Galaxy S4 Mini I9195.[Firmware for rest of the countries and carrier will be added here when available]
Previous Firmware Build
Samsung Galaxy Pocket Plus GT-S5310B [Complete Guide] S5310BVJAMJ2 Android 4.1.2 Jelly Bean Firmware
How to Install Android 4.2.2 Jelly Bean Official Firmware on Galaxy S4 Mini I9195 through Odin:
- Download Android 4.2.2 XXUBMK3 Firmware for Galaxy S4 Mini I9195 from the above list
- Download Odin 3.07
- Switch off your phone and boot Galaxy S4 Mini I9195 into Download Mode by pressing and holding the Volume Down+Home+Power buttons (long press until the boot screen appear), now press Volume Up key to proceed to Download Mode.
- Extract the downloaded Odin3.07 zip file and run the Odin3 v3.07.exe file as an administrator (Right click on the .exe file and click on Run as administrator)
- Now connect your Galaxy S4 Mini I9195 to your computer via USB cable
- In Odin3 screen, you should see a COM Port number like “0:[COM7]” at ID:COM section and “Added!” text at the message box. This means your device has been detected by Odin3.
- Make sure that, only the “Auto Reboot” and “F. Reset Time” options are checked.
- Now, extract the downloaded firmware zip file, you’ll find a firmware file with extension .tar.md5
- In Odin screen, click on PDA button and select the firmware file with .tar.md5 extension (The firmware file look something like: I9195XXDLJ5_I9195ODDDLI7_INU.tar.md5)
- Now, click on the Start button to begin the installation process, wait few moments.
- Once completed, you would see “PASS!” message in ID:COM port having green background
- Your phone should automatically reboot after completion
- You can now disconnect your phone from computer
- Finish
Wednesday, October 22, 2014
Blackberry 9500 Cellular Phone Lcd Light Repair Solution
blackberry 9500 cellular phone lcd light repair solution,blackberry 9500 cellular phone lcd light not working repair solution,blackberry 9500 cellular phone lcd light jumper solution,blackberry 9500 cellular phone lcd light repair guide,blackberry 9500 cellular phone lcd light line damage solution,blackberry 9500 cellular phone lcd light jumper guide solution,blackberry 9500 cellular phone lcd light tips and tricks here 1005 working solution here if u have blackberry 9500 no light lc i have this solution 100% i need light line damage solution i have tested damage solution see my solution many time tested me my solution here see this
blackberry 9105 cellular phone pearl sim card repair solution
see this diagram many time tested me this solution 1st reheat this ic i hope solve your phone working reheat but not done 2nd try change this ic 100% working i tested this 100% working this solution i hope done and dont forget visit my blog.
Saturday, October 18, 2014
Tips and Tricks on Audio Power Amplifier Circuit
Amplilfier power series from the beginning until now did not experience any changes. Some say this series is good, but the series was good fitting assembly and tested the results are not as we expected.
The problem is usually treble is less subtle, less sound, sound breaking, buzz, middle of the field tested the bass sound is lost. so you do not have to believe what people 100%. The quality amplifier built-up would differ greatly with the amplifier assembly, a series can be the same but the quality will depend on who manufacture it.Here are a few tricks to try
How to cope with a buzzing sound
Power amplifiers are often used in the field blazer. This circuit is said said person is a bell assembly. But you do not immediately interested in this power, the circuit rather complicated and difficult to understand reflect the intelligence of people who first mendisainnya. In my opinion a great power is the power of simple, inexpensive, easily assembled and rational. You do not need to use expensive components such as the price of tantalum capacitors, power mosfet and the other expensive. This does not determine the quality of the power amp so that we raft. Power of sometimes causing buzzing, to overcome that is by holding the line input jack ground to the ground with 10-22 ohm resistors. So do not just take the ground input from the ground but held first with the R 10 ohms.
How to setting bias trimpot
Rotate the trimpot bias (if any) until the drain current of 50-100mA on each power transistor, in order to avoid defects treble in volume in the top position at 10. The risks are so panassss heatsink! (This setting marks on plate A-AB)
Offset trimpot setting
At the time of input without a signal, turn the trimpot so that the voltage on the speaker offsets actually read 0 volts. If you do not want to bother, use and entrust it with ic type series from Hitachi HA17741 IC brand quality or other! This is the heart of the series, 90-95% of quality is determined from the IC circuit this!
Overcoming the voice
Use pre-amp circuit to increase the signal of at least 2 times. normally and should pre-amp circuit uses IC op-amps with +12 V minimum supply-12V. Raise his mid tone!
If hard you do not want to just use the tone control circuit IC is his mid!
The secret is not in his mid tone alone, but the signal output from the IC op-amps are usually large.
Treble rupture
Excessive treble will damage the power amp, power rather than out even ngedrop. Handle, attach the filter capacitor on the input 1NF power amp to ground to ensure the signal is not disabled. Always use a quality active components such as ICs and transistors, 500 price difference will also be different results.
Use a large cable and short as possible, especially for leg power transistor, and this transistor should be directly soldered to the pcb.
Missing bass in field
Usually power for field use supplay CT 50V 50V transformer, or at least 42V 42V ct. The greater the greater the supply voltage watt channeled though the series is written only 300-400 Watts only. This course uses Elko capacitors with voltage 80-100V. 10.000uF/100V capacitor will be equal to 4X10.000uF/50V and of course voltage capacitor is filled with full / almost full.
Try to use a strong Elko at temperatures of 105 C. Capacitors are strong in supply of more than nominal voltage is written on his body. For example 4700uF/50V 85C capacitor will quickly explode in voltage 51V 85C. And Elko will be strong 105C 4700uF/50V voltage supplied more than 50V at a temperature of 85C. Elco so that it does not quickly explode if given the full voltage, keep its temperature as cold as possible, fan with the cool air.
For speaker
Try using a driver speakers that have a large spool diameter fitted with a suitable size bok. Usually included examples of the parameters / dimensions bok. Size bok bok2 usually larger than that sold in the market. if you force using bok that from this market, use driver type G12-80 (sorry no fear brand called promotion) speakers with bass tones to wall size small. Bok wall should be thick, strong and do not forget glued! Bok who will not be glued with a different sound, especially bass tones, prove it!
Heat Sensor
The form of transistor, the transistor is usually type BD139 MJE340 or it could be located in the center, flanked by a pair of transistors having a certain equal. These transistors must be mounted on the main heatsink to detect the heat generated by power transistors. It acts to lower bias currents at the hot heatsink. So what heatsink and power transistors must be set diposisi hot? Yes objectives nothing to prevent the signal from the defect (in class A or AB), with consequent heat. This class is not necessary and will not be felt if you only want the bass tones only. Goal setting on. AB grade is still crystal clear sound even though the maximum volume positioned rotated (in the middle of the field).
It is unlikely, but its closer.
Large heatsink
Not only electrolytic capacitors are more explosive at high temperatures, power transistors can also break away under stress break the original. For example 2SC5200 transistors have the break voltage of 230Vdc, but if temperaturya high voltage values will break his fall well below this value, resulting in faster transistor is damaged. Use of heatsink and cooling fan is very important not only to reduce the heat, more than it can prevent the transistor from break / damaged and weakened output. Increasingly hot temperatures will be more or less ability. Use of this cooling is expected for the components remain fresh, fit and durability.
Choice Component
Power Transistor
There are so many types and models of these transistors, for example MJ15003 MJ15024-4 and-5 from Motorola, but unfortunately these components are not manufactured by Motorola again but from ON semiconductor. Transistor model jengkol usually stronger in the high temperature, probably due to more airtight. 2SC5200 from Toshiba, this transistor is equal dalamannya Sanken 2SC2922 Korea, and both will break if the temperature is too hot. 2SC2922 Sanken issued tin granules when heated, this weakness, the Japanese technology is better than Korean technology. 2SC3281, this transistor is the most popular and frequently used in professional amplifier, but Toshiba does not produce much, if still there in the market, then it most likely is fake!
Transfomer
There are two models of the transformer which is often used, namely EI model (box / conventional) and the model toroid (ring / donut). Some say the toroid transformer model is better because it has a smaller flux leak, in fact the same. Circuits that are sensitive to this flux is high berpenguatan circuits like pre-amp head and mic pre-amp. The circuit is usually installed horizontally / flat parallel to the structure of a conventional transformer wire so that a series of emails received reverberation is greater. Unlike the model toroid transformer is arranged in a vertical wire their email so that the wires are perpendicular to circuit kits The effect is the flux of the pre-amp kit receive a smaller head. To solve for this flux does not enter the series is by downloading shelding / fortified with non-magnetic plate such as aluminum plate and copper plate / sheet pcb board. Plate is of course connected to ground via a cable. To match the flux in a vertical transmission, the conventional transformer needs to be installed side (the side be side down) so that the arrangement of transformer wire stand upright, this method is often used in built-up POWER2. Voltage 50V 50V CT can be obtained by combining the two transformer 25VCT25V, CT is not used, the foot 25V 50V so that the legs be made only to CT, bringing the total number is 100V or 50VCT50V. It deserves used for pwr amp powerless over 400Watt.
Resistor 5 Watt
Resistor on the power transistor legs are usually valued at 0.5 ohm 5 Watt white square. If we dismantle dalamannya it appears there was a circular aluminum wire. It resembles the inductor, the inductive reactance inductor will be higher when fed a high-frequency fractions so that treble tone will be weakened and deformed. Power required to remove the high notes (treble) of course greater, there is a problem here. The use of R 0.5/5W on its home-based power amplifier ok-ok only. But often do not realize the cause of damage to the speakers and power amplifiers is the high treble tones. Treble is not out but was hit by a pwr amp so arising is hot and damaged. We recommend using common Watt resistor 2 12:47 - 1 ohm parallel 2 so that counted 4 Watt. Or if you use 0:22 ohm 2 Watt Resitor unnecessary because the voltage clamp diparalel quite half (one R 0.5/5W replaced one R 0.22/2W) its ok.
Fuse
Nature damage to semiconductor materials / transistor power amplifier is short, if you use a supply that is high enough then the destruction of these transistors will invite their partners to be damaged as well. In order for the destruction of this transitor congregation not need the installation of fuses. 1.5A per power transistor is considered sufficient.
Friday, October 17, 2014
Nokia X2 02 Ringer problem solution ways
If you have ringer problem in Nokia X2-02 you will not be able to hear music and ring tones will not ring properly in it. Low ringer voice in Nokia X2-02 can be also due to water damages or broken parts. Damage components can be cause of no ringer voice in it.Nokia X2-05 Lcd Display Jumper Ways Problem Solution
Replace the ringer and check if it is working good. Nosie in ringing can be due to ringer pwoblem. Look at diagram above this diagram have some tracks to solve Nokia X2-02 ringer problem solution.
A diagram that is attached with this post this diagram have two different color lines that are identfing tracks and parts that are used in ringer function of Nokia X2-02.You can check all these components with meter and apply jumpers if any of them are missing or damage.
for more detail and new tips and tricks about cellphone service problem keep visiting this page we will update cellphone service diagrams timely with new cellphone diagrams.some related post are also given bellow you can read them also for more information about cellphone.
Replace the ringer and check if it is working good. Nosie in ringing can be due to ringer pwoblem. Look at diagram above this diagram have some tracks to solve Nokia X2-02 ringer problem solution.
A diagram that is attached with this post this diagram have two different color lines that are identfing tracks and parts that are used in ringer function of Nokia X2-02.You can check all these components with meter and apply jumpers if any of them are missing or damage.
for more detail and new tips and tricks about cellphone service problem keep visiting this page we will update cellphone service diagrams timely with new cellphone diagrams.some related post are also given bellow you can read them also for more information about cellphone.
Nokia 6125 Keypad Problem
Nokia 6125 Keypad Ways,
Nokia 6125 Keypad IC Jumper,
Nokia 6125 keypad Tracks,
Nokia 6125 keypad jumpers
Thursday, October 16, 2014
Nokia Asha 203 Mic problem solution jumper ways
Nokia asha 203 mic problem, Low voice in nokia asha 203, Mic is not working in nokia asha 203.All these mic faults can be solve with a few simple steps that I am posting in this post.A mic repairing diagram for nokia asha 203 is also attached with this post.Nokia Asha 203 Ringer problem solution ways
If you find som carbon or water damages in the mother board. Clean these parts with electronics cleaner and apply heat with hot air to make it dry. Much heat can damage the nokia asha 203 mother board.
In diagram above you can see two different color lines these lines are given to identify components that are used in mic function of nokia asha 203.Check all these tracks with meter and if any link is break apply jumpers as given in nokia asha 203 mic repairing diagram above.
for more detail and new tips and tricks about cellphone service problem keep visiting this page we will update cellphone service diagrams timely with new cellphone diagrams.some related post are also given bellow you can read them also for more information about cellphone.
If you find som carbon or water damages in the mother board. Clean these parts with electronics cleaner and apply heat with hot air to make it dry. Much heat can damage the nokia asha 203 mother board.
In diagram above you can see two different color lines these lines are given to identify components that are used in mic function of nokia asha 203.Check all these tracks with meter and if any link is break apply jumpers as given in nokia asha 203 mic repairing diagram above.
for more detail and new tips and tricks about cellphone service problem keep visiting this page we will update cellphone service diagrams timely with new cellphone diagrams.some related post are also given bellow you can read them also for more information about cellphone.
Wednesday, October 15, 2014
Dual Sim IC Repair Dual Sim IC Ways and Jumper 02
Dual Sim IC Repair Dual Sim IC Ways and Jumper 02
How to Transfer Files Using Media Transfer Mode Via Wi Fi on Sony Xperia Z2 Tablet
Transferring files in Sony Xperia Z2 Tablet is now made easy by using the Media Transfer Mode. You can easily transfer files between your device and other MTP compatible devices such as computer, using a Wi-Fi connection. But before you can transfer files wirelessly, you will need to pair both devices.Note: You will need a Wi-Fi enabled devices that supports Media transfer such as a computer running Microsoft, Windows Vista orWindows 7.
To pair your device with the computer:
- Check if the media transfer mode of your device is enabled. It is normally enabled by default.
- Using the USB cable, connect your device to a computer.
- On your computer, once the name of your device appear, click on Network Configuration and just follow the steps on how to pair the computer.
- After pairing, safely disconnect your device from your computer.
These steps will work only on Windows 7 OS and the computer is connected to the Wi-Fi Access point via network cable.
To connect paired devices wirelessly in Media Transfer Mode:
- First things first, check if the media transfer mode is enabled.
- On your Home Lcd, tap on the Menu icon.
- Select Settings > Xperia > USB connectivity.
- Then tap the paired device that you want to connect to under Trusted devices.
- Tap connect.
If you want to disconnect, just tap on the paired device and tap Disconnect.
If you want to remove the paired device, tap on the paired device you want to remove and select Forget.
Tuesday, October 14, 2014
Nokia 103 Battery Terminal Points Damage Ways Problem Solution
Nokia 103 Battery Terminal Points Damage Ways Problem Solution if in nokia 103 during changing battery terminal points you have loss battery points then you can solve this problem with this diagram bellow posted in this post.
Nokia 105 Light ic Jumper Solution Ways Free
there are three different color lines in this post shows that how you can make jumpers so check these links with meter and if any of them is broken make these jumpers with insulation wire.this diagram can help you in case nokia 103 is dead you can check these links so that battery crunt can pass through right ways and can be set on off.
for more detail and new tips and tricks about this problem keep visiting this page we will update it timely with new diagrams.some related post are also given bellow you can read them also for more information.
Nokia 105 Light ic Jumper Solution Ways Free
there are three different color lines in this post shows that how you can make jumpers so check these links with meter and if any of them is broken make these jumpers with insulation wire.this diagram can help you in case nokia 103 is dead you can check these links so that battery crunt can pass through right ways and can be set on off.
for more detail and new tips and tricks about this problem keep visiting this page we will update it timely with new diagrams.some related post are also given bellow you can read them also for more information.
nokia c2 01 speaker problem solution
nokia c2-01 speaker problem
nokia c2 ear speaker solution
nokia c2-01 ear speaker problem
nokia c2-01 speaker problem
nokia c2-01 speaker ways
nokia c2-01 speaker problem
c2-01 earpiece speaker solution
c2 speaker ways
nokia c2-01 ear speaker ways
nokia c2-01 speaker solution
c2-01 speaker problem
If replacement of speaker could not solve problem check all these tracks that are given in above diagram to solve ear piece problem.If any print out of these is missing apply jumpers and if any part is missing or damage replace them.
nokia c2 ear speaker solution
nokia c2-01 ear speaker problem
nokia c2-01 speaker problem
nokia c2-01 speaker ways
nokia c2-01 speaker problem
c2-01 earpiece speaker solution
c2 speaker ways
nokia c2-01 ear speaker ways
nokia c2-01 speaker solution
c2-01 speaker problem
If replacement of speaker could not solve problem check all these tracks that are given in above diagram to solve ear piece problem.If any print out of these is missing apply jumpers and if any part is missing or damage replace them.
Monday, October 13, 2014
nokia 6600s camera standby solution
nokia 6600s camera standby solution
solution for nokia 6600s camera on standby,
nokia 6600s camera on standby solution,
nokia 6600s camera standby solution,
camera 6600s standby solution,
ssolution for nk. 6600s camera onstandby
solution for nokia 6600s camera on standby,
nokia 6600s camera on standby solution,
nokia 6600s camera standby solution,
camera 6600s standby solution,
ssolution for nk. 6600s camera onstandby
Sunday, October 5, 2014
How to Factory Reset Hard Reset iPhone 5S
iPhone 5S is the latest iPhone model from Apple. Restoring the default settings or factory reset your iPhone 5S will delete all your saved files. It is recommended to backup your important files on your computer before attempting to reset your device.Why do we need to reset the device? We have our own reasons why we factory reset our device. Maybe we want to delete all the files and restore the device to its original state. It could also be the device may be malfunctioning or so slow and it needs to be reset.
Step 1. On your iPhone, go to "Settings".
Step 2. Select "General" option.
Step 3. On the bottom of the Lcd, tap "Reset".
Step 4. You will be seeing a list of things which you can reset. If you want to reset all the content, select "Erase All Content and Settings".
Step 5. Tap "Yes" to confirm the action.
Now, you just need to wait while your iPhone 5S is wiping all datas or files on your device. In a short while your device will be good as new.
In case your iPhone 5S is unresponsive or frozen, you may need to hard reset your device. Press and hold the "Power Button" and the "Home Key Button" at the same time for at least ten seconds until the Apple logo appears.
Thursday, October 2, 2014
Samsung Galaxy Ace GT S5830 S3 Evolutioned CynogenMod Rom
As I know You guyz would be Searching for a Rom where you can Make your smartphone much faster and over there I always try to get U the Same over.. So this rom is Quite like dat one only with less power consumng features and instant boot up etc...This rom is Just Likely Tweeked up to the one which are of New Samsung Galaxy S3 Evolutioned Rom and have been modded up to it!!!
HOW TO FLAST THE ROM:-
Feautures found Over:-
1)TouchwizUX from galaxy S3 (MDPI)
2)Based on CyanogenMod 9.0.4-RC1-MacławStudios
3)SGIII Real accu weather
4)Samsung galaxy s3 WallpaperChooser
5)SGSIII Icons
6)SGSIII Sounds
7)MusicHub Hub 3.0
8)SGSIII Live Wallpapers
9)S-voice Modded
10)Swype key
11)SG3 Clock widget
12)KiesCast
13)Application monitor widget
14)Memo
15)PicsPlay
16)Family Story
17)Polaris Office
18)You tube
19)Stock Video Player
20)Prima Wifi File
21)S suggest
22)Flipboard
23)Chat on
24)Samsung Apps
25)facebook Sns Account
26)Samsung Account Service
27)Postit
2)Based on CyanogenMod 9.0.4-RC1-MacławStudios
3)SGIII Real accu weather
4)Samsung galaxy s3 WallpaperChooser
5)SGSIII Icons
6)SGSIII Sounds
7)MusicHub Hub 3.0
8)SGSIII Live Wallpapers
9)S-voice Modded
10)Swype key
11)SG3 Clock widget
12)KiesCast
13)Application monitor widget
14)Memo
15)PicsPlay
16)Family Story
17)Polaris Office
18)You tube
19)Stock Video Player
20)Prima Wifi File
21)S suggest
22)Flipboard
23)Chat on
24)Samsung Apps
25)facebook Sns Account
26)Samsung Account Service
27)Postit
CHANGELOG
- remove temporary S2 touchwizclok i have some problem to recompil it ( i provide stock ace vertion for now)
- Nims Kernel V2.1
- Camera taking pictures , preview is working,settings working
(Sometimes camera service cant connect to camera - you must reopen application.)
- tweak Laucher stay in persistant memory
- missing Language added
- Mdpi TwCalculator
- Improve battery life tenfold by PureMotive
- Fix boot problem
- fix googleplay issue
- Apollo music player removed aand replaced by Miui themed Music player
- remove temporary S2 touchwizclok i have some problem to recompil it ( i provide stock ace vertion for now)
- Nims Kernel V2.1
- Camera taking pictures , preview is working,settings working
(Sometimes camera service cant connect to camera - you must reopen application.)
- tweak Laucher stay in persistant memory
- missing Language added
- Mdpi TwCalculator
- Improve battery life tenfold by PureMotive
- Fix boot problem
- fix googleplay issue
- Apollo music player removed aand replaced by Miui themed Music player
HOW TO FLAST THE ROM:-
[So Here am I with for the one You waiting For and Scrolling too.. Now Ill give u a perfect Way to Flash this Custom Rom... You would be Thinking this one Would be as Same as the one which Normally others are but not Like it Now.!! This One is Quite Different from Others.]
Before Flashing the Rom you Need to Root your Device to Avoid Administrational Settings.
If You Dont know to HOW TO ROOT Your Samsung Galaxy Ace Click Here.
If you Have already Rooted.. Procede further..
Procedure For Upgrading To Samsung Galaxy S3 Modded Rom is Quite Very Much Simple.. Follow the Steps Exactly Noted Below to Avoid Your Phone Getting Bricked Up or Having Any Other Issue Over..
Before install S3-Evolution-Beta3 :
I recommand Do a full wipe Before install for better Experience
Installation of S3-Evolution-Beta-3-Ultimate you need Ext3 or Ext4 Partition
Here is a tutorilal for Partition Your Sd-Card..
I recommand Do a full wipe Before install for better Experience
Installation of S3-Evolution-Beta-3-Ultimate you need Ext3 or Ext4 Partition
Here is a tutorilal for Partition Your Sd-Card..
Partition your sd-card:
Simplest way is to use "MiniTool Partition Wizard Home Edition" from http://www.partitionwizard.com/download.html
This tool is compatible with Windows 2000/XP/Vista & Windows 7
requirements: USB SD Card reader.
pull SD card from phone, insert into USB SD Card reader,you can do it with your usb cable mount Sd-crad. Windows should report new drive and content of the drive should be visible.
• step 1: Delete Old Partitions on SD card
[Note: this partition manager QUEUES the operations. So nothing is deleted and changed UNTIL you click "APPLY" and then confirm by clicking "OK".
WARNING! ]
Make sure you are Deleting Partition on SD card! (not your hard drive for example)
This step Deletes everything on SD card, so backup files first!
Dont be afraid, just read everything and think twice before selecting correct drive.
Do you see three gray icons on the bottom? Under each of them the capacity of each drive is listed, and SD CARD has slightly different icon.
Hard drives on the Lcdshot have 465.8GB and 74.5GB, and on the bottom, the SD card, with 3.8GB capacity.
• step 2: create FAT or FAT32 partition “ note that this partition is for storing your media, etc..”
select "Create As": PRIMARY
Select "File System:" FAT when you have 2GB or smaller card.
Select "File System:" FAT32 when you have 4GB or greater card.
• step 3: select the 2nd partition and select "Create As": PRIMARY
NOTE:
Stock roms with stock kernel will support fat32
Stock roms with custom kernels “ like CF-Root” may support both fat32/ext4 “check their threads”
Cm7/cm9 roms will support ext4
Here Is a NOTE:
For a wired reason, in both cm7/cm9 roms if formatted your 2nd partition with ext4 format, link2sd wont create mount script, unless you have selected ext3 “although the format was converted to ext4”
• step 4: finish
finally, click "apply" button on top left corner.
partitions will be created and card will be formatted.
Reattach your sd card to your phone and turn it on. (you can also do it With usb Connection )
Chose your Vertion Of Beta3 , Light or Ultimate copy it to sd-card
Reboot your phone to ClockWorkMod
Flash ClockWorkMod 5:
http://forum.xda-developers.com/atta...=743333&d=1318...
Install from sd-card
the Phone Reboot Automaticaly when installation Done
if It stay on blank Lcd remove the Baterry an turn on again
For better Performance :
go to settings , performance, processor, cpu governor select SmartassV2
dont forget to set on boot ^^
you can disable Surface Dithering
to have better Ui bar go to settings system notification drawler Widget buttons then select one more Toggle you can hide indicator too..
Simplest way is to use "MiniTool Partition Wizard Home Edition" from http://www.partitionwizard.com/download.html
This tool is compatible with Windows 2000/XP/Vista & Windows 7
requirements: USB SD Card reader.
pull SD card from phone, insert into USB SD Card reader,you can do it with your usb cable mount Sd-crad. Windows should report new drive and content of the drive should be visible.
• step 1: Delete Old Partitions on SD card
[Note: this partition manager QUEUES the operations. So nothing is deleted and changed UNTIL you click "APPLY" and then confirm by clicking "OK".
WARNING! ]
Make sure you are Deleting Partition on SD card! (not your hard drive for example)
This step Deletes everything on SD card, so backup files first!
Dont be afraid, just read everything and think twice before selecting correct drive.
Do you see three gray icons on the bottom? Under each of them the capacity of each drive is listed, and SD CARD has slightly different icon.
Hard drives on the Lcdshot have 465.8GB and 74.5GB, and on the bottom, the SD card, with 3.8GB capacity.
• step 2: create FAT or FAT32 partition “ note that this partition is for storing your media, etc..”
select "Create As": PRIMARY
Select "File System:" FAT when you have 2GB or smaller card.
Select "File System:" FAT32 when you have 4GB or greater card.
• step 3: select the 2nd partition and select "Create As": PRIMARY
NOTE:
Stock roms with stock kernel will support fat32
Stock roms with custom kernels “ like CF-Root” may support both fat32/ext4 “check their threads”
Cm7/cm9 roms will support ext4
Here Is a NOTE:
For a wired reason, in both cm7/cm9 roms if formatted your 2nd partition with ext4 format, link2sd wont create mount script, unless you have selected ext3 “although the format was converted to ext4”
• step 4: finish
finally, click "apply" button on top left corner.
partitions will be created and card will be formatted.
Reattach your sd card to your phone and turn it on. (you can also do it With usb Connection )
Chose your Vertion Of Beta3 , Light or Ultimate copy it to sd-card
Reboot your phone to ClockWorkMod
Flash ClockWorkMod 5:
http://forum.xda-developers.com/atta...=743333&d=1318...
Install from sd-card
the Phone Reboot Automaticaly when installation Done
if It stay on blank Lcd remove the Baterry an turn on again
For better Performance :
go to settings , performance, processor, cpu governor select SmartassV2
dont forget to set on boot ^^
you can disable Surface Dithering
to have better Ui bar go to settings system notification drawler Widget buttons then select one more Toggle you can hide indicator too..
Subscribe to:
Posts (Atom)