Showing posts with label install. Show all posts
Showing posts with label install. Show all posts
Monday, September 22, 2014
How to Root Samsung Galaxy Star Pro S7262 Using Android 4 1 2 Jelly Bean Firmware and Install CWM Recovery
Samsung has already released the Android 4.1.2 Jelly Bean update with firmware build number S7262XXUAMK5 for the Galaxy Star Pro with dual SIM card slot (GT-S7262). The new official firmware is now available as an Over-The-Air (OTA) update as well as through Samsung KIES.
Firmware details
PDA: S7262XXUAMK5
CSC: S7262ODDAMK2
MODEM: S7262XXUAMK2
Version: Android 4.1.2
Build date: Nov 23, 2013
Regions: India, Nepal, Sri Lanka, Bangladesh
Samsung Galaxy Star Pro S7262 users who missed the OTA update notification or unable to access the update over Samsung KIES, can now download and install the same manually using our step-by-step guide.
PDA: S7262XXUAMK5
CSC: S7262ODDAMK2
MODEM: S7262XXUAMK2
Version: Android 4.1.2
Build date: Nov 23, 2013
Regions: India, Nepal, Sri Lanka, Bangladesh
Samsung Galaxy Star Pro S7262 users who missed the OTA update notification or unable to access the update over Samsung KIES, can now download and install the same manually using our step-by-step guide.
Pre-requisites
1. Install USB Drivers for Samsung Galaxy Star Pro on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy Star Pro should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 percent.
6. The Android 4.1.2 XXUAMK5 Jelly Bean firmware is compatible only with the Samsung Galaxy Star Pro (GT-S7262). Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Star Pro by navigating to Settings >> About Phone.
Files Required
1. Android 4.1.2 XXUAMK5 Jelly Bean Firmware (Mirror Link 1, Link 2)
2. Odin 3.07 (Mirror Link)
Steps to Update Galaxy Star Pro S7262 with Android 4.1.2 XXUAMK5 Jelly Bean Firmware
Step 1: Extract Firmware zip file using WinRAR/7-Zip/WinZip or any other extracting tool, you will get a .tar.md5 file and some other files (optional).
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Switch off the Galaxy Star Pro.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down, Home and Power buttons together until a construction Android robot icon with a warning triangle appears on Lcd. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy Star Pro to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn to light blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.
Note: If the Added message does not appear, then try re-install USB drivers or changing the port on the computer.
Step 7: Select the following files in Odin from extracted S7262XXUAMK5 firmware folder:
1. Install USB Drivers for Samsung Galaxy Star Pro on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy Star Pro should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 percent.
6. The Android 4.1.2 XXUAMK5 Jelly Bean firmware is compatible only with the Samsung Galaxy Star Pro (GT-S7262). Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Star Pro by navigating to Settings >> About Phone.
Files Required
1. Android 4.1.2 XXUAMK5 Jelly Bean Firmware (Mirror Link 1, Link 2)
2. Odin 3.07 (Mirror Link)
Steps to Update Galaxy Star Pro S7262 with Android 4.1.2 XXUAMK5 Jelly Bean Firmware
Step 1: Extract Firmware zip file using WinRAR/7-Zip/WinZip or any other extracting tool, you will get a .tar.md5 file and some other files (optional).
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Switch off the Galaxy Star Pro.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down, Home and Power buttons together until a construction Android robot icon with a warning triangle appears on Lcd. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy Star Pro to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn to light blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.
Note: If the Added message does not appear, then try re-install USB drivers or changing the port on the computer.
Step 7: Select the following files in Odin from extracted S7262XXUAMK5 firmware folder:
- Click the PDA button and select the .tar.md5 file.
- Click the Phone button and select file with MODEM in its name. Ignore if there is no such file.
- Click the CSC button and select file with CSC in its name. Ignore if there is no such file.
- Click the PIT button and select the .pit file. Ignore if there is no such file.
Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the Start button to begin the installation process.
Step 10: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from the computer.
Samsung Galaxy Star Pro S7262 should be now updated with official Android 4.1.2 XXUAMK5 Jelly Bean. Head over to Settings >> About Phone to verify the software version running on the device.
Note: If Galaxy Star Pro S7262 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the Start button to begin the installation process.
Step 10: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from the computer.
Samsung Galaxy Star Pro S7262 should be now updated with official Android 4.1.2 XXUAMK5 Jelly Bean. Head over to Settings >> About Phone to verify the software version running on the device.
Note: If Galaxy Star Pro S7262 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.
Sunday, September 21, 2014
How to Install Android 4 3 UBUGMK6 JB Firmware on Galaxy S3 I9300
Samsung has now launched Android 4.3 Jelly Bean is UBUGMK6 official firmware update for the Galaxy S3 GT-I9300. Updates the firmware was launched in various countries including Brazil one of them, and also can be downloaded for a manual update. This new firmware update just brings bug fixes and performance tweaks on the Galaxy S3 GT-I9300 you. Well right Keep reading this guide to learn further how to get an official stock Android 4.3 Jelly Bean I9300UBUGMK6 firmware running on the Galaxy S3 GT-I9300. Almost all possible ways in this alloy to update your device to this firmware discussed here. One thing to note that the official firmware flashing or installing the recovery kernel root access you will fail, in short it will unroot.
I9300UBUGMK6 Android 4.3 Jelly Bean firmware stok tersedia di kedua OTA dan Kies mengupdate. Namun, jika Anda tidak bisa mendapatkannya dari sana maka Anda bisa selalu menyala I9300UBUGMK6 Android 4.3 Jelly Bean firmware pada Galaxy S3 GT-I9300 manual. Kami akan membicarakan semua metode pembaruan yang tersedia. Anda harus selalu mencoba OTA atau metode Kies pertama dan ketika kedua metode tidak bekerja maka hanya mencoba flashing manual.
Warning: This tutorial is only for Galaxy S3 GT-I9300. Don’t try this guide on any other Android device. Also, we are not responsible for any damage caused due to the instruction given in this page. Try this at your own risk. However, it is very unlikely that your device will be damaged if you follow all the instructions as it is which are mentioned in procedure.
Pre Requisites:
Though official firmware restore all existing data but we recommend to back up your data first before proceeding to avoid any uncomfortable situation such as bootloop fix.
1. Backup your device data.
2. Make sure your device have at least 60% battery power. You can install an app like Battery Notifier BT Free on your Android device to check it easily.
3. You already have USB Driver Installed for Galaxy S3 GT-I9300 in your PC. Download USB Drivers
4. Make sure USB Debugging is enabled otherwise you won’t able to transfer file between PC and Galaxy
S3 GT-I9300.How To Update Galaxy S3 GT-I9300 via OTA
- First of all make sure you have stable internet connection (Wi-Fi or data network) on your device.
- Now, go to Android app drawer and then select Settings.
- Then locate About Device and tap on it.
- Next select Software update from About device Lcd.
- Then tap on Update option.
- You should see an update, press OK to download and install. (Remember, download using 3G or network data will incur additional charges to your phone bill!)
- Soon your device will reboot to complete the installation process.
How To Update Galaxy S3 GT-I9300 via Kies
- Make sure you have stable internet connection on your computer.
- Now download and install Samsung Kies on your computer.
- Turn on your device (if it off) and then connect it to computer with USB cable.
- Run Samsung Kies and wait for it to detect your device.
- You should see a New Firmware Upgrade is available at Samsung Kies home Lcd.
- Press the Firmware Upgrade button to proceed.
- Follow on Lcd instruction and soon you will see your device running upgrade and reboot automatically. Once done, you can disconnect your device from computer.
Again! If you see “This is the latest firmware” in Samsung Kies, then your device yet to receive the latest update on Kies. Its good time to go for manual update instruction that located below.
I9300UBUGMK6 Android 4.3 Jelly Bean Firmware Details:
PDA: I9300UBUGMK6
CSC: I9300ZTOUGMK3
Download: I9300UBUGMK6 I9300ZTOUGMK3_ZTO.zip
Please Note: After flashing this firmware you will lost any installed custom ROM including CM10.2, AOKP, Avatar,Beanstalk, Omni ROM, Slim ROM, Pac-Man, Paranoid Android, LiquidSmooth or Carbon.
How To Install I9300UBUGMK6 Android 4.3 Jelly Bean On Galaxy S3 GT-I9300 Manually
- Download Odin v3.09.
- Extract Firmware zip file that you downloaded earlier from above link, you will get a .tar.md5 file and some other files (optional).
- Extract Odin zip file and you will get Odin3 v3.09.exe along with few other files.
- Power off your Android device. Wait 5-6 seconds for vibration to confirm complete switch off.
- Now, put the Galaxy S3 GT-I9300 in Download Mode by pressing and holding down the Home & Volume Down button together while pressing the Power button. A warning Lcd will come up; press Volume Up button to enter Download Mode.
- Now run Odin3 v3.09.exe (see Step 3) as an Administrator because Admin privileges is required to complete the process smoothly (only applicable Windows Vista and higher).
- Now connect your device to your PC using USB cable. An “Added!!” massage will appear in Odin’s message box. If you don’t get the same then you should try another USB port (try USB port located in back in your desktop PC). If that too don’t work then you should reinstall the driver. If you successfully see the “Added!!” message in Odin then you are ready to go in next step. You should also see COM port with a number in Yellow if you successfully added your device.
- Click the AP Button, and select that .tar.md5 file that you get in Step 2.
- In Odin window, make sure only Auto Reboot and F. Reset Time checkboxes are selected.
- Double check everything that we mentioned in Step 8 & Step 9 above. Now, once satisfied hit the START button to begin the flashing process.
- Once flashing completed, your Galaxy S3 GT-I9300 will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.
Fix Boot Loop Issue On Galaxy S3 GT-I9300
If Galaxy S3 GT-I9300 stuck at booting animation for more than 10 minutes after Step 11 then follow below instructions:
- Go to recovery mode. To do so, press and hold the Volume Up, Home and Power buttons together.
- Now perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option.
That’s it! Let us know about your latest Android 4.3 Jelly Bean experience. visit and get more info ....
Wednesday, September 17, 2014
Samsung Galaxy Mega 5 8 I9152 with Android 4 2 2 XWUANA5 Jelly Bean Official Firmware Install Odin Guide
Firmware details
PDA: I9152XWUANA5
CSC: I9152OJVANA2
MODEM: I9152XXUAML4
Version: Android 4.2.2
Build date: Jan 29, 2014
Regions: Egypt, Afghanistan, Algeria, Iran, Kenya, Morocco, Nigeria, Pakistan, Saudi Arabia, South Africa, Tunisia, United Arab Emirates
Samsung Galaxy Mega 5.8 I9152 users who missed the OTA update notification or unable to access the update over Samsung KIES, may follow our step-by-step guide to install the update manually.
Pre-requisites
1. Install USB Drivers for Samsung Galaxy Mega 5.8 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy Mega 5.8 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 percent.
6. The Android 4.2.2 XWUANA5 Jelly Bean firmware is compatible only with the Samsung Galaxy Mega 5.8 (GT-I9152). Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Mega 5.8 by navigating to Settings >> About Phone.
Files Required
1. Android 4.2.2 XWUANA5 Jelly Bean Firmware (Mirror Link) for Galaxy Mega 5.8 I9152
2. Odin 3.07
Steps to Update Galaxy Mega 5.8 I9152 with Android 4.2.2 XWUANA5 Jelly Bean Firmware
Step 1: Extract Firmware zip file using WinRAR/7-Zip/WinZip or any other extracting tool, you will get a .tar.md5 file and some other files (optional).
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Switch off the Galaxy Mega 5.8.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down, Home and Power buttons together until a construction Android robot icon with a warning triangle appears on Lcd. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy Mega 5.8 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn to light blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.
Note: If the Added message does not appear, then try re-install USB drivers or changing the port on the computer.
Related Article :Samsung Galaxy Mega 5.8 I9152 with Android 4.2.2 XWUANA6 Jelly Bean Official Firmware & How to Update Using Odin Guide Step 7: Select the following files in Odin from extracted I9152XWUANA5 firmware folder:
- Click the PDA button and select the .tar.md5 file.
- Click the Phone button and select file with MODEM in its name. Ignore if there is no such file.
- Click the CSC button and select file with CSC in its name. Ignore if there is no such file.
- Click the PIT button and select the .pit file. Ignore if there is no such file.
Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the Start button to begin the installation process.
Step 10: Once the installation process completes, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect it from the computer.
Samsung Galaxy Mega 5.8 I9152 should be now updated with Android 4.2.2 XWUANA5 Jelly Bean official firmware. Head over to Settings >> About Phone to verify the software version running on the device.
Note: If Galaxy Mega 5.8 I9152 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.
Click here to know How to Root Galaxy Mega 5.8 I9152 running on Android 4.2.2 Jelly Bean firmware.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the Start button to begin the installation process.
Step 10: Once the installation process completes, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect it from the computer.
Samsung Galaxy Mega 5.8 I9152 should be now updated with Android 4.2.2 XWUANA5 Jelly Bean official firmware. Head over to Settings >> About Phone to verify the software version running on the device.
Note: If Galaxy Mega 5.8 I9152 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.
Click here to know How to Root Galaxy Mega 5.8 I9152 running on Android 4.2.2 Jelly Bean firmware.
Thursday, September 11, 2014
How To Guide Install UBUEMK4 Android 4 3 JB Firmware on Galaxy Note 2 N7100
Samsung has just launched the Android 4.3 Jelly Bean UBUEMK4 official firmware update for Galaxy Note GT - N7100 2 . This firmware update has been released in various countries , including one of her Brazil and the Dominican Republic , and also can be downloaded for manual updates . You can also update your device firmware via Kies or OTA update . Because of this smartphone comes equipped with Jelly Bean Android 4.1.2 out of the box , this new firmware update will upgrade your smartphone to the OS which is certainly better that Android 4.3 Jelly Bean . Well Continue reading this guide to learn more about how to get an official stock Android 4.3 Jelly Bean N7100UBUEMK4 firmware that runs on the Galaxy Note GT - N7100 2 . Almost all the possible ways to update your device to this firmware discussed here . and the need to remember or One thing should be noted that the flashing or installing the official firmware kernel then restore your root access will be canceled , in short it will unroot it .
Android 4.3 Jelly Bean N7100UBUEMK4 stock firmware available in both OTA and Kies update. However, if you can not get it from there then you can always blink N7100UBUEMK4 Android 4.3 Jelly Bean firmware on Galaxy Note GT-N7100 manual 2. We will discuss all the methods available updates. You should always try OTA or Kies method first and when the two methods do not work then just try flashing manually.
Pre Requisites:
Though official firmware restore all existing data but we recommend to back up your data first before proceeding to avoid any uncomfortable situation such as bootloop fix.
1. Backup your device data.
2. Make sure your device have at least 60% battery power. You can install an app like Battery Notifier BT Free on your Android device to check it easily.
3. You already have USB Driver Installed for Galaxy Note 2 GT-N7100 in your PC.Download USB Drivers
4. Make sure USB Debugging is enabled otherwise you won’t able to transfer file between PC and Galaxy Note 2 GT-N7100.
Warning: This tutorial is only for Galaxy Note 2 GT-N7100. Don’t try this guide on any other Android device. Also, we are not responsible for any damage caused due to the instruction given in this page. Try this at your own risk. However, it is very unlikely that your device will be damaged if you follow all the instructions as it is which are mentioned in procedure.
How To Update Galaxy Note 2 GT-N7100 via OTA
- First of all make sure you have stable internet connection (Wi-Fi or data network) on your device.
- Now, go to Android app drawer and then select Settings.
- Then locate About Device and tap on it.
- Next select Software update from About device Lcd.
- Then tap on Update option.
- You should see an update, press OK to download and install. (Remember, download using 3G or network data will incur additional charges to your phone bill!)
- Soon your device will reboot to complete the installation process.
If you see “The latest update have already been installed” massage while checking update then your device yet to receive an OTA update. Check back within few days or jump to next procedure
.How To Update Galaxy Note 2 GT-N7100 via Kies
- Make sure you have stable internet connection on your computer.
- Now download and install Samsung Kies on your computer.
- Turn on your device (if it off) and then connect it to computer with USB cable.
- Run Samsung Kies and wait for it to detect your device.
- You should see a New Firmware Upgrade is available at Samsung Kies home Lcd.
- Press the Firmware Upgrade button to proceed.
- Follow on Lcd instruction and soon you will see your device running upgrade and reboot automatically. Once done, you can disconnect your device from computer.
Again! If you see “This is the latest firmware” in Samsung Kies, then your device yet to receive the latest update on Kies. Its good time to go for manual update instruction that located below.
Note: You can install any firmware listed below despite availability in other countries, except those which comes with carrier name.
N7100UBUEMK4 Android 4.3 Jelly Bean Firmware Downloads
Please Note: After flashing this firmware you will lost any installed custom ROM including CM10.2, AOKP, Avatar,Beanstalk, Omni ROM, Slim ROM, Pac-Man, Paranoid Android, LiquidSmooth or Carbon.
How To Install N7100UBUEMK4 Android 4.3 Jelly Bean On Galaxy Note 2 GT-N7100 Manually
- Download Odin v3.09.
- Extract Firmware zip file that you downloaded earlier from above link, you will get a .tar.md5 file and some other files (optional).
- Extract Odin zip file and you will get Odin3 v3.09.exe along with few other files.
- Power off your Android device. Wait 5-6 seconds for vibration to confirm complete switch off.
- Now, put the Galaxy Note 2 GT-N7100 in Download Mode by pressing and holding down the Home &Volume Down button together while pressing the Power button. A warning Lcd will come up; press Volume Up button to enter Download Mode.
- Now run Odin3 v3.09.exe (see Step 3) as an Administrator because Admin privileges is required to complete the process smoothly (only applicable Windows Vista and higher).
- Now connect your device to your PC using USB cable. An “Added!!” massage will appear in Odin’s message box. If you don’t get the same then you should try another USB port (try USB port located in back in your desktop PC). If that too don’t work then you should reinstall the driver. If you successfully see the “Added!!” message in Odin then you are ready to go in next step. You should also see COM port with a number in Yellow if you successfully added your device.
- Click the AP Button, and select that .tar.md5 file that you get in Step 2.
- In Odin window, make sure only Auto Reboot and F. Reset Time checkboxes are selected.
- Double check everything that we mentioned in Step 8 & Step 9 above. Now, once satisfied hit the START button to begin the flashing process.
- Once flashing completed, your Galaxy Note 2 GT-N7100 will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.
Congrats! You just updated your Galaxy Note 2 GT-N7100 to Android 4.3 Jelly Bean firmware. Go to Settings > About device to verify this firmware update.
Fix Boot Loop Issue On Galaxy Note 2 GT-N7100
If Galaxy Note 2 GT-N7100 stuck at booting animation for more than 10 minutes after Step 11 then follow below instructions:
- Go to recovery mode. To do so, press and hold the Volume Up, Home and Power buttons together.
- Now perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option.
Please note, performing wiping task will erase your device internal memory data and not external SD card data.
That’s it! Let us know about your latest Android 4.3 Jelly Bean experience.
Sunday, September 7, 2014
How To Install DXUAML3 Android 4 1 2 Jelly Bean Firmware on Galaxy Star Pro Duos S7262 Guide
Samsung launches Android 4.1.2 DXUAML3 official Jelly Bean firmware update for the Galaxy Pro Duos GT-S7262 Star. The firmware update is launched in various countries including Thailand and the Philippines, and also can be downloaded for manual updates. This new firmware update brings bug fixes and performance tweaks on the Galaxy Pro Duos GT-S7262 Star. Continue reading this guide to learn how to get an official stock S7262DXUAML3 Jelly Bean Android 4.1.2 firmware running on the Galaxy Pro Duos GT-S7262 Star.
Warning: This tutorial is only for Galaxy Star Pro Duos GT-S7262. Don’t try this guide on any other Android device. Also, we are not responsible for any damage caused due to the instruction given in this page. Try this at your own risk. However, it is very unlikely that your device will be damaged if you follow all the instructions as it is which are mentioned in procedure.
Pre Requisites:
Though official firmware restore all existing data but we recommend to back up your data first before proceeding to avoid any uncomfortable situation such as bootloop fix.
1. Backup your device data. You can follow our ultimate backup guide.
2. Make sure your device have at least 60% battery power. You can install an app like Battery Notifier BT Free on your Android device to check it easily.
3. You already have USB Driver Installed for Galaxy Star Pro Duos GT-S7262 in your PC. [Download USB Drivers]
4. Make sure USB Debugging is enabled otherwise you won’t able to transfer file between PC and Galaxy Star Pro Duos GT-S7262. [Guide].
How To Update Galaxy Star Pro Duos GT-S7262 via OTA
- First of all make sure you have stable internet connection (Wi-Fi or data network) on your device.
- Now, go to Android app drawer and then select Settings.
- Then locate About Device and tap on it.
- Next select Software update from About device Lcd.
- Then tap on Update option.
- You should see an update, press OK to download and install. (Remember, download using 3G or network data will incur additional charges to your phone bill!)
- Soon your device will reboot to complete the installation process.
If you see “The latest update have already been installed” massage while checking update then your device yet to receive an OTA update. Check back within few days or jump to next procedure.
How To Update Galaxy Star Pro Duos GT-S7262 via Kies
- Make sure you have stable internet connection on your computer.
- Now download and install Samsung Kies on your computer.
- Turn on your device (if it off) and then connect it to computer with USB cable.
- Run Samsung Kies and wait for it to detect your device.
- You should see a New Firmware Upgrade is available at Samsung Kies home Lcd.
- Press the Firmware Upgrade button to proceed.
- Follow on Lcd instruction and soon you will see your device running upgrade and reboot automatically. Once done, you can disconnect your device from computer
Again! If you see “This is the latest firmware” in Samsung Kies, then your device yet to receive the latest update on Kies. Its good time to go for manual update instruction that located below.
[Note: You can install any firmware listed below despite availability in other countries, except those which comes with carrier name.]
S7262DXUAML3 Android 4.1.2 Jelly Bean Firmware Downloads
- Thailand: S7262DXUAML3 S7262OLBAML3_THL.zip
- Philippines (Sun): S7262DXUAML3 S7262OLBAML3_XTC.zip
- Philippines (Globe): S7262DXUAML3 S7262OLBAML3_GLB.zip
- Philippines (Smart): S7262DXUAML3 S7262OLBAML3_SMA.zip
How To Install S7262DXUAML3 Android 4.1.2 Jelly Bean On Galaxy Star Pro Duos GT-S7262 Manually
- Download Odin v3.09.
- Extract Firmware zip file that you downloaded earlier from above link, you will get a .tar.md5 file and some other files (optional).
- Extract Odin zip file and you will get Odin3 v3.09.exe along with few other files.
- Power off your Android device. Wait 5-6 seconds for vibration to confirm complete switch off.
- Now, put the Galaxy Star Pro Duos GT-S7262 in Download Mode by pressing and holding down the Home &Volume Down button together while pressing the Power button. A warning Lcd will come up; press Volume Up button to enter Download Mode.
- Now run Odin3 v3.09.exe (see Step 3) as an Administrator because Admin privileges is required to complete the process smoothly (only applicable Windows Vista and higher).
- Now connect your device to your PC using USB cable. An “Added!!” massage will appear in Odin’s message box. If you don’t get the same then you should try another USB port (try USB port located in back in your desktop PC). If that too don’t work then you should reinstall the driver. If you successfully see the “Added!!” message in Odin then you are ready to go in next step. You should also see COM port with a number in Yellow if you successfully added your device.
- Click the AP Button, and select that .tar.md5 file that you get in Step 2. If you are using old Odin then add the file to PDA button.
- In Odin window, make sure only Auto Reboot and F. Reset Time checkboxes are selected.
- Double check everything that we mentioned in Step 8 & Step 9 above. Now, once satisfied hit the START button to begin the flashing process.
- Once flashing completed, your Galaxy Star Pro Duos GT-S7262 will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.
Congrats! You just updated your Galaxy Star Pro Duos GT-S7262 to Android 4.1.2 Jelly Bean firmware. Go toSettings > About device to verify this firmware update.
Fix Boot Loop Issue On Galaxy Star Pro Duos GT-S7262
If Galaxy Star Pro Duos GT-S7262 stuck at booting animation for more than 10 minutes after Step 11 then follow below instructions:
- Go to recovery mode. To do so, press and hold the Volume Up, Home and Power buttons together.
- Now perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option.
Please note, performing wiping task will erase your device internal memory data and not external SD card data.
That’s it! Let us know about your latest Android 4.1.2 Jelly Bean experience.
Saturday, September 6, 2014
Install Jelly Bean 4 1 2 XXUBMEA OTA Update for Samsung Galaxy S4 I9500
The XXUBMEA firmware has been released last week for the I9505 Snapdragon Galaxy S4 smartphone, now you can install the same version of it but designed to work with the Exynos 5 Octa Galaxy S4 variant. Read this entire post and you should be able to complete the updating process in under 10 minutes.
If you didn’t receive the official OTA Update to XXUBMEA Jelly Bean 4.1.2 firmware, then you should use this guide to manually flash all the required files. The new update fixes several bugs that were present in the previous builds that were delivered with the Galaxy S4. More info about this update can be found here. In order to successfully complete the update, you will first have to take a look at the guidelines below:
If you encountered problems with the update, then you should take a look at the notes below.
NOTE 1: if ODIN froze, it showed an error message or some other thing blocked the update from installing correctly, then you should disconnect the phone from computer. Close ODIN and remove the phone’s battery. Re-insert the battery after several seconds have passed and then you will need to repeat the entire tutorial once again until your device will boot with the new OS.
NOTE 2: if ODIN says that the update has been installed correctly, but the phone doesn’t go past the Samsung boot animation, then you will need to ‘factory reset’ the device using the Recovery mode. This means that you will have to read the extra steps listed below:
Read More..
If you didn’t receive the official OTA Update to XXUBMEA Jelly Bean 4.1.2 firmware, then you should use this guide to manually flash all the required files. The new update fixes several bugs that were present in the previous builds that were delivered with the Galaxy S4. More info about this update can be found here. In order to successfully complete the update, you will first have to take a look at the guidelines below:
- use this guide only with the Samsung Galaxy S4 I9500 Exynos 5 Octa model. Don’t try to flash this firmware update on any other variant of the Galaxy S4 phone.
- if your phone is rooted, then this update will revoke root access.
- try to backup some of your most important files before starting the updating process.
- if your smartphone doesn’t want to boot after you install XXUBMEA firmware, then you will be forced to apply some extra steps. You will need to boot into Recovery mode and factory reset the phone, which will delete data from your device.
- download and install Samsung USB Drivers for your computer. Without these drivers your phone won’t be recognized by your computer and you will be forced to return here and reinstall them.
- make sure that your PC doesn’t have the Samsung KIES software running while the ODIN program installs the new firmware update. Odin is a small program that is commonly used to flash tar.md5 files and other similar updating files for Samsung phones.
- disable all the antivirus and other security applications from running on your computer.
- enable USB Debugging from your phone’s Developer Options. If this menu doesn’t show up in Settings, then you need to open ‘About device’ section and then scroll down to ‘Build Number’. Tap the build number section 7 times for the Developer Options menu to be enabled.
- make sure that you read the entire post before starting the update.
- your phone’s battery power levels should be over 50%, as this will prevent it from powering off in the middle of the updating process.
- don’t skip any steps that I have listed below, as you wouldn’t want to repeat the entire tutorial more than once.
- this is a guide for advanced Android users and you shouldn’t attempt to use it in case you don’t know what you’re doing, as that will result in a failed attempt.
- we cannot be blamed in case you lose any important files or you’ll brick the device in the process.
- if you cannot complete the update, then you can ask for extra help in comments.
How to flash Android 4.1.2 XXUBMEA Jelly Bean OTA Update for the Samsung Galaxy S4 I9500:
- Download the I9500XXUBMEA zip from HERE. Extract the contents of this file and save them on your PC desktop.
> you will get a file that is titled ‘I9500XXUBMEA_I9500OLBBMEA_XSE.tar.md5‘. Don’t extract any further than that. - Download Odin3 v3.07 from HERE. Extract the zip and place the files on your computer’s desktop screen.
- Power off your smartphone completely.
- Boot the device into Download Mode like this.
- Launch the Odin exe on your computer.
- Now, connect the device with your PC via USB cable.
> wait for ODIN to say that the new device has been ‘added!!’ and then you can continue to the next step.
> if the phone isn’t recognized, then you should plug it into another USB port or reinstall the Samsung USB Drivers using the download link listed in the preparation guide. - Next, click the ‘PDA’ button and find the I9500XXUBMEA_I9500OLBBMEA_XSE.tar.md5 file. Load it into Odin.
> don’t change any other default ODIN settings and make sure that Re-Partition option is not enabled. - Click the START button to begin the updating process and then wait several minutes for all the files to be successfully installed on your device.
- When the update is complete ODIN will display a confirmation message and your Galaxy S4 Exynos 5 Octa phone will restart.
- Unplug the phone from PC when the Samsung logo screen appears.
- Wait for the phone to boot into normal mode and that should be all.
- Test all the new features and then tell us in comments if the overall performance of your device has been improved by the XXUBMEA Jelly Bean update.
If you encountered problems with the update, then you should take a look at the notes below.
NOTE 1: if ODIN froze, it showed an error message or some other thing blocked the update from installing correctly, then you should disconnect the phone from computer. Close ODIN and remove the phone’s battery. Re-insert the battery after several seconds have passed and then you will need to repeat the entire tutorial once again until your device will boot with the new OS.
NOTE 2: if ODIN says that the update has been installed correctly, but the phone doesn’t go past the Samsung boot animation, then you will need to ‘factory reset’ the device using the Recovery mode. This means that you will have to read the extra steps listed below:
- power off your Galaxy S4 completely by removing its battery.
- re-insert the battery and then boot the phone into stock Recovery Mode.
- select ‘wipe data/ factory reset’ option and confirm this process.
- when the factory reset has been correctly applied, select ‘reboot system now’.
- wait for your device to boot into normal mode.
Thursday, September 4, 2014
How To Install XXAMG1 Android 4 1 2 JB Firmware on Galaxy Fame S6810 Guide
Samsung launches Android 4.1.2 firmware update XXAMG1 official Jelly Bean for Galaxy GT-S6810 Fame. The firmware update is launched in various countries including Afghanistan, Saudi Arabia, Tunisia, Pakistan, Iraq, Egypt and Morocco, and also can be downloaded for manual updates. You can also update your device firmware via Kies or OTA update. Because the device comes with Android 4.1.2 Jelly Bean out of the box, this new firmware update just brings bug fixes and performance tweaks. Continue reading this guide to learn how to get an official stock S6810XXAMG1 Jelly Bean Android 4.1.2 firmware running on the GT-S6810 Galaxy fame....
Warning: This tutorial is only for Galaxy Fame GT-S6810. Don’t try this guide on any other Android device. Also, we are not responsible for any damage caused due to the instruction given in this page. Try this at your own risk. However, it is very unlikely that your device will be damaged if you follow all the instructions as it is which are mentioned in procedure.
Pre Requisites:
Though official firmware restore all existing data but we recommend to back up your data first before proceeding to avoid any uncomfortable situation such as bootloop fix.
1. Backup your device data. You can follow our ultimate backup guide.
2. Make sure your device have at least 60% battery power. You can install an app like Battery Notifier BT Free on your Android device to check it easily.
3. You already have USB Driver Installed for Galaxy Fame GT-S6810 in your PC. [Download USB Drivers]
4. Make sure USB Debugging is enabled otherwise you won’t able to transfer file between PC and Galaxy Fame GT-S6810.
How To Update Galaxy Fame GT-S6810 via OTAThough official firmware restore all existing data but we recommend to back up your data first before proceeding to avoid any uncomfortable situation such as bootloop fix.
1. Backup your device data. You can follow our ultimate backup guide.
2. Make sure your device have at least 60% battery power. You can install an app like Battery Notifier BT Free on your Android device to check it easily.
3. You already have USB Driver Installed for Galaxy Fame GT-S6810 in your PC. [Download USB Drivers]
4. Make sure USB Debugging is enabled otherwise you won’t able to transfer file between PC and Galaxy Fame GT-S6810.
- First of all make sure you have stable internet connection (Wi-Fi or data network) on your device.
- Now, go to Android app drawer and then select Settings.
- Then locate About Device and tap on it.
- Next select Software update from About device screen.
- Then tap on Update option.
- You should see an update, press OK to download and install. (Remember, download using 3G or network data will incur additional charges to your phone bill!)
- Soon your device will reboot to complete the installation process.
How To Update Galaxy Fame GT-S6810 via Kies
Make sure you have stable internet connection on your computer.
Now download and install Samsung Kies on your computer.
Turn on your device (if it off) and then connect it to computer with USB cable.
Run Samsung Kies and wait for it to detect your device.
You should see a New Firmware Upgrade is available at Samsung Kies home screen.
Press the Firmware Upgrade button to proceed.
Follow on screen instruction and soon you will see your device running upgrade and reboot automatically. Once done, you can disconnect your device from computer.
Make sure you have stable internet connection on your computer.
Now download and install Samsung Kies on your computer.
Turn on your device (if it off) and then connect it to computer with USB cable.
Run Samsung Kies and wait for it to detect your device.
You should see a New Firmware Upgrade is available at Samsung Kies home screen.
Press the Firmware Upgrade button to proceed.
Follow on screen instruction and soon you will see your device running upgrade and reboot automatically. Once done, you can disconnect your device from computer.
Again! If you see “This is the latest firmware” in Samsung Kies, then your device yet to receive the latest update on Kies. Its good time to go for manual update instruction that located below.
[Note: You can install any firmware listed below despite availability in other countries, except those which comes with carrier name.]
S6810XXAMG1 Android 4.1.2 Jelly Bean Firmware Downloads
- Afghanistan: S6810XXAMG1 S6810OJVAMF2_AFG.zip
- Saudi Arabia: S6810XXAMG1 S6810OJVAMF2_KSA.zip
- Tunisia: S6810XXAMG1 S6810OJVAMF2_TUN.zip
- Pakistan (PAK): S6810XXAMG1 S6810OJVAMF2_PAK.zip
- Iraq: S6810XXAMG1 S6810OJVAMF2_MID.zip
- Egypt: S6810XXAMG1 S6810OJVAMF2_EGY.zip
- Morocco (MWD): S6810XXAMG1 S6810OJVAMF2_MWD.zip
- Morocco: S6810XXAMG1 S6810OJVAMF2_FWD.zip
[Please Note: After flashing this firmware you will lost any installed custom ROM including CM10.2, AOKP, Avatar,Beanstalk, Omni ROM, Slim ROM, Pac-Man, Paranoid Android, LiquidSmooth or Carbon.]
How To Install S6810XXAMG1 Android 4.1.2 Jelly Bean On Galaxy Fame GT-S6810 Manually
- Download Odin v3.09.
- Extract Firmware zip file that you downloaded earlier from above link, you will get a .tar.md5 file and some other files (optional).
- Extract Odin zip file and you will get Odin3 v3.09.exe along with few other files.
- Power off your Android device. Wait 5-6 seconds for vibration to confirm complete switch off.
- Now, put the Galaxy Fame GT-S6810 in Download Mode by pressing and holding down the Home & Volume Down button together while pressing the Power button. A warning screen will come up; press Volume Up button to enter Download Mode.
- Now run Odin3 v3.09.exe (see Step 3) as an Administrator because Admin privileges is required to complete the process smoothly (only applicable Windows Vista and higher).
- Now connect your device to your PC using USB cable. An “Added!!” massage will appear in Odin’s message box. If you don’t get the same then you should try another USB port (try USB port located in back in your desktop PC). If that too don’t work then you should reinstall the driver. If you successfully see the “Added!!” message in Odin then you are ready to go in next step. You should also see COM port with a number in Yellow if you successfully added your device.
- Click the AP Button, and select that .tar.md5 file that you get in Step 2. If you are using old Odin then add the file to PDA button.
- In Odin window, make sure only Auto Reboot and F. Reset Time checkboxes are selected.
- Double check everything that we mentioned in Step 8 & Step 9 above. Now, once satisfied hit the START button to begin the flashing process.
- Once flashing completed, your Galaxy Fame GT-S6810 will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.
Congrats! You just updated your Galaxy Fame GT-S6810 to Android 4.1.2 Jelly Bean firmware. Go to Settings > About device to verify this firmware update.
Fix Boot Loop Issue On Galaxy Fame GT-S6810
If Galaxy Fame GT-S6810 stuck at booting animation for more than 10 minutes after Step 11 then follow below instructions:
- Go to recovery mode. To do so, press and hold the Volume Up, Home and Power buttons together.
- Now perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option.
Please note, performing wiping task will erase your device internal memory data and not external SD card data.
That’s it! Let us know about your latest Android 4.1.2 Jelly Bean experience.
Tuesday, August 26, 2014
UFSx HWK Install Files Mirrors Install Instructions Guide
UFSx_Support_Suite_Setup_v02.03.00.06.exe - UFSx_Support_Suite_Setup_v02.03.00.06.exe
DHLT Files - Samsung Fast Code Calc Tables
DHT.part01.exe - DHLT.part01.exe - DHLT.part01.exe
DHT.part02.rar - DHLT.part02.rar - DHLT.part02.rar
DHT.part03.rar - DHLT.part03.rar - DHLT.part03.rar
DHT.part04.rar - DHLT.part04.rar - DHLT.part04.rar
DHT.part05.rar - DHLT.part05.rar - DHLT.part05.rar
DHT.part06.rar - DHLT.part06.rar - DHLT.part06.rar
DHT.part07.rar - DHLT.part07.rar - DHLT.part07.rar
1. Uninstall ALL previous versions, you MUST uninstall HWK Suite BEFORE trying to uninstall HWK Support Suite Setup. 2. Install UFSx Support Suite Setup 3. Connect your UFSx+HWK before running the UFSx Control Panel 4. Run UFSx Control Panel 5. Switch to the "Hardware" Tab 6. If you only have one UFSx connected it will be selected, if more than one, select the check box next to the required UFSx. You can click "Scan Boxes" to refresh the list if you have connected further boxes since opening the Control Panel 7. Click "Check Box" 8. Click "Update Box" 9. Click "Check Box" - Make sure "Box Status" = "True" or "Bad Software" and "Server Status" = "Support Ok", before proceeding 10. Switch to the "Software" Tab 11. Amend "Application Install Path" and/or "Nokia Install Path", if required. 12. Click "Check Server" 13. Click "Install" 14. If you have more than 1 UFSx+HWK run steps 5-13 for each UFSx+HWK (NOTE: You must install something at step 13)
How to install same UFSx+HWK to 2nd PC.
Same as above and you must complete ALL steps.
How to add further UFSx+HWK after initial install.
Steps 4-13 as above
DHLT Files
Should be extracted and installed too:-
C:Program FilesSarasSoftUFSUFS_SAMs\_DHT for 32bit PCs
C:Program Files (x86)SarasSoftUFSUFS_SAMs\_DHT for 64bit PCs
DHLT Files - Samsung Fast Code Calc Tables
DHT.part01.exe - DHLT.part01.exe - DHLT.part01.exe
DHT.part02.rar - DHLT.part02.rar - DHLT.part02.rar
DHT.part03.rar - DHLT.part03.rar - DHLT.part03.rar
DHT.part04.rar - DHLT.part04.rar - DHLT.part04.rar
DHT.part05.rar - DHLT.part05.rar - DHLT.part05.rar
DHT.part06.rar - DHLT.part06.rar - DHLT.part06.rar
DHT.part07.rar - DHLT.part07.rar - DHLT.part07.rar
1. Uninstall ALL previous versions, you MUST uninstall HWK Suite BEFORE trying to uninstall HWK Support Suite Setup. 2. Install UFSx Support Suite Setup 3. Connect your UFSx+HWK before running the UFSx Control Panel 4. Run UFSx Control Panel 5. Switch to the "Hardware" Tab 6. If you only have one UFSx connected it will be selected, if more than one, select the check box next to the required UFSx. You can click "Scan Boxes" to refresh the list if you have connected further boxes since opening the Control Panel 7. Click "Check Box" 8. Click "Update Box" 9. Click "Check Box" - Make sure "Box Status" = "True" or "Bad Software" and "Server Status" = "Support Ok", before proceeding 10. Switch to the "Software" Tab 11. Amend "Application Install Path" and/or "Nokia Install Path", if required. 12. Click "Check Server" 13. Click "Install" 14. If you have more than 1 UFSx+HWK run steps 5-13 for each UFSx+HWK (NOTE: You must install something at step 13)
How to install same UFSx+HWK to 2nd PC.
Same as above and you must complete ALL steps.
How to add further UFSx+HWK after initial install.
Steps 4-13 as above
DHLT Files
Should be extracted and installed too:-
C:Program FilesSarasSoftUFSUFS_SAMs\_DHT for 32bit PCs
C:Program Files (x86)SarasSoftUFSUFS_SAMs\_DHT for 64bit PCs
Friday, August 22, 2014
How To Install VRUCML1 Android 4 3 JB Firmware on Verizon Galaxy S3 SCH I535 Guide
Verizon Galaxy S3 SCH-I535 users VRUCML1 finally received the official Android 4.3 firmware update Jelly Bean. The firmware update is available as an OTA update and also can be downloaded for manual updates. This new firmware update may upgrade Verizon Galaxy S3 SCH-I535 from the official Android 4.1.2 to Android 4.3 Jelly Bean Jelly Bean. Continue reading this guide to learn how to get an official stock Android 4.3 Jelly Bean I535VRUCML1 firmware runs on Verizon Galaxy S3 SCH-I535. Almost all the possible ways to update your device to this firmware discussed here. One thing should be noted that the official firmware flashing or install kernel then restore root access you will fail, in short it will unroot it.
Warning:
This tutorial is only for Verizon Galaxy S3 SCH-I535. Don’t try this guide on any other Android device. Also, we are not responsible for any damage caused due to the instruction given in this page. Try this at your own risk. However, it is very unlikely that your device will be damaged if you follow all the instructions as it is which are mentioned in procedure.
Pre Requisites:
Though official firmware restore all existing data but we recommend to back up your data first before proceeding to avoid any uncomfortable situation such as bootloop fix.
1. Backup your device data. You can follow our ultimate backup guide.
2. Make sure your device have at least 60% battery power. You can install an app like Battery Notifier BT Free on your Android device to check it easily.
3. You already have USB Driver Installed for Verizon Galaxy S3 SCH-I535 in your PC. [Download USB Drivers]
4. Make sure USB Debugging is enabled otherwise you won’t able to transfer file between PC and Verizon Galaxy S3 SCH-I535. [Guide].
How To Update Verizon Galaxy S3 SCH-I535 via OTA
- First of all make sure you have stable internet connection (Wi-Fi or data network) on your device.
- Now, go to Android app drawer and then select Settings.
- Then locate About Device and tap on it.
- Next select Software update from About device screen.
- Then tap on Update option.
- You should see an update, press OK to download and install. (Remember, download using 3G or network data will incur additional charges to your phone bill!)
- Soon your device will reboot to complete the installation process.
If you see “The latest update have already been installed” massage while checking update then your device yet to receive an OTA update. Check back within few days or jump to next procedure.
How To Update Verizon Galaxy S3 SCH-I535 via Kies
- Make sure you have stable internet connection on your computer.
- Now download and install Samsung Kies on your computer.
- Turn on your device (if it off) and then connect it to computer with USB cable.
- Run Samsung Kies and wait for it to detect your device.
- You should see a New Firmware Upgrade is available at Samsung Kies home screen.
- Press the Firmware Upgrade button to proceed.
- Follow on screen instruction and soon you will see your device running upgrade and reboot automatically. Once done, you can disconnect your device from computer.
Again! If you see “This is the latest firmware” in Samsung Kies, then your device yet to receive the latest update on Kies. Its good time to go for manual update instruction that located below.
I535VRUCML1 Android 4.3 Jelly Bean Firmware Details:
- PDA: I535VRUCML1
- CSC: I535VZWCML1
- Download: I535VRUCML1 I535VZWCML1_VZW.zip
[Please Note: After flashing this firmware you will lost any installed custom ROM including CM10.2, AOKP, Avatar,Beanstalk, Omni ROM, Slim ROM, Pac-Man, Paranoid Android, LiquidSmooth or Carbon.]
How To Install I535VRUCML1 Android 4.3 Jelly Bean On Verizon Galaxy S3 SCH-I535 Manually
- Download Odin v3.09.
- Extract Firmware zip file that you downloaded earlier from above link, you will get a .tar.md5 file and some other files (optional).
- Extract Odin zip file and you will get Odin3 v3.09.exe along with few other files.
- Power off your Android device. Wait 5-6 seconds for vibration to confirm complete switch off.
- Now, put the Verizon Galaxy S3 SCH-I535 in Download Mode by pressing and holding down the Home &Volume Down button together while pressing the Power button. A warning screen will come up; press Volume Up button to enter Download Mode.
- Now run Odin3 v3.09.exe (see Step 3) as an Administrator because Admin privileges is required to complete the process smoothly (only applicable Windows Vista and higher).
- Now connect your device to your PC using USB cable. An “Added!!” massage will appear in Odin’s message box. If you don’t get the same then you should try another USB port (try USB port located in back in your desktop PC). If that too don’t work then you should reinstall the driver. If you successfully see the “Added!!” message in Odin then you are ready to go in next step. You should also see COM port with a number in Yellow if you successfully added your device.
- Click the AP Button, and select that .tar.md5 file that you get in Step 2. If you are using old Odin then add the file to PDA button.
- In Odin window, make sure only Auto Reboot and F. Reset Time checkboxes are selected.
- Double check everything that we mentioned in Step 8 & Step 9 above. Now, once satisfied hit the START button to begin the flashing process.
- Once flashing completed, your Verizon Galaxy S3 SCH-I535 will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.
Congrats! You just updated your Verizon Galaxy S3 SCH-I535 to Android 4.3 Jelly Bean firmware. Go to Settings > About device to verify this firmware update.
Fix Boot Loop Issue On Verizon Galaxy S3 SCH-I535
If Verizon Galaxy S3 SCH-I535 stuck at booting animation for more than 10 minutes after Step 11 then follow below instructions:
- Go to recovery mode. To do so, press and hold the Volume Up, Home and Power buttons together.
- Now perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option.
Please note, performing wiping task will erase your device internal memory data and not external SD card data.
That’s it! Let us know about your latest Android 4.3 Jelly Bean experience.
Subscribe to:
Posts (Atom)